F5 Turbine Nosecone Assembly - Includes new spindle/collet, wave/plate Washers, 24 Vane Impeller, Ceramic Bearings - Both rear & front flanged (sealed for dust & debris protection, lube-free, radial or angular designed with o-rIngs), 7 jet port injector manifold, Fluted brass nosecone with 10 seated exhaust ports, New housing o-ring. Fully Assembled, just screw on to the Vortex F5 housing. Your choice of bearing and spindle type.
Male Brass Hose Barb 1/8 NPT. Push on to 1/8 to 3/16 inch inside diameter hose. Threads are 1/8-27 NPT. These are used for the Speed Control Foot Pedal.
F5 Turbine Bearing Service - Includes new sealed ceramic lube free bearings with your choice of Radial or Angular, wave/plate washers, o-rings - Both rear & front flanged bearings are sealed for dust & debris protection.
Valveless fittings are completely interchangeable. Fitting halves seal with a twist; replaceable O-rings eliminate leaks. Use to disconnect tool from air supply. Fitting is 1/8" ID (fits our air hose). Rated to 100 psi.
The Vortex Router Base (VRB) attachment is finally here! Specifically designed for the Vortex High Speed Carver, the VRB is precision milled from Aerospace aluminum in a user friendly ergonomic shape. The VRB will take your Vortex to the next level allowing you to precision carve the perfect uniform depth to inlay precious metals, stones, woods and/or epoxies like a pro! It also allows you to carve perfect depth lettering and borders as well. Its hourglass shape with a wide front viewing port makes it easy to see what you're doing and the chamfered face is milled to remove the sharp edge to provide a smooth router movement. The VRB gives you complete control over the depth at which you are engraving. Simply slide it onto the end of the Vortex carver and tighten the three set screws with the allen wrench provided and you're really to carve. The 3 Stainless Steel set screws have nylon points which provide extra gripping strength while at the same time will not scratch or mar the surface of your Vortex carver and will allow you to lock down the router at any desired depth. Get the Vortex Router Base attachment today and add an entire new dimension to your engraving! Just a reminder that we also sell spare set screws and allen wrenches in case you lose them as they are quite small. Ordering a spare set will keep you from having down time waiting for a separate order to be shipped to you in case you lose them.
These 30 hole aluminum bur holders are designed to hold standard FG type burs or any bur with a 1/16 inch (1.6mm) diameter shaft. Anodized colors vary (gold shown in photo.)
Organize your burs with this 24 holes high quality plastic bur holder. Designed to hold standard FG type burs or any bur with a 1/16 inch (1.6mm) diameter shaft. Colors vary.
Female Brass Industrial Plug 1/4 NPT. Makes it easy to connect your air hose to your air compressor. If you have our air compressor with a quick release, get this matching part. It makes your air connections a snap!
4" Magnetic Polished Stainless Steel Bur Tray. Stop losing burs! Put all your burs into the magnetic bur tray and pick and choose the ones you need for your project.
Male Brass Hose Barb 1/4 NPT. Push on to 1/8 to 3/16 inch inside diameter hose. Threads are 1/4 NPT. Connect to your air compressor or filter and air hose.
This brass hose barb splicer allows you to connect two air hoses together by pushing the hose on to the barb. The splicer is designed for air hose with 1/8 inch inside diameter, like the hose that comes with most carvers and extra length of hose in this section. This splicer is all brass construction, will not rust or corrode. Precision machined to high quality standards.
2020 Unbridled, LLC. All rights reserved. All prices are in USD.