The Vortex Router Base (VRB) attachment is finally here! Specifically designed for the Vortex High Speed Carver, the VRB is precision milled from Aerospace aluminum in a user friendly ergonomic shape. The VRB will take your Vortex to the next level allowing you to precision carve the perfect uniform depth to inlay precious metals, stones, woods and/or epoxies like a pro! It also allows you to carve perfect depth lettering and borders as well. Its hourglass shape with a wide front viewing port makes it easy to see what you're doing and the chamfered face is milled to remove the sharp edge to provide a smooth router movement. The VRB gives you complete control over the depth at which you are engraving. Simply slide it onto the end of the Vortex carver and tighten the three set screws with the allen wrench provided and you're really to carve. The 3 Stainless Steel set screws have nylon points which provide extra gripping strength while at the same time will not scratch or mar the surface of your Vortex carver and will allow you to lock down the router at any desired depth. Get the Vortex Router Base attachment today and add an entire new dimension to your engraving! Just a reminder that we also sell spare set screws and allen wrenches in case you lose them as they are quite small. Ordering a spare set will keep you from having down time waiting for a separate order to be shipped to you in case you lose them.
F5 Turbine Nosecone Assembly - Includes new spindle/collet, wave/plate Washers, 24 Vane Impeller, Ceramic Bearings - Both rear & front flanged (sealed for dust & debris protection, lube-free, radial or angular designed with o-rIngs), 7 jet port injector manifold, Fluted brass nosecone with 10 seated exhaust ports, New housing o-ring. Fully Assembled, just screw on to the Vortex F5 housing. Your choice of bearing and spindle type.
F5 Turbine Bearing Service - Includes new sealed ceramic lube free bearings with your choice of Radial or Angular, wave/plate washers, o-rings - Both rear & front flanged bearings are sealed for dust & debris protection.
This valve controls the speed of your tool. Simply turn the knob to your desired speed from shut off to full speed and everything in between. Can be used with tank and tankless air compressors.
Our "Premium Grade" turbine lubrication is our lightest viscosity and is rated a meets H1 and 3H lubricant standards." Our premium grade turbine lubrication is non-toxic and formulated in accordance with the criteria established by for H1 and 3H lubricants. Warning: Do not use with Vortex F5 or carvers with permanently lubricated bearings.
Teflon® tape, also know as PTFE tape, is used to make a tight seal the threads for our brass hose barbs. With the threads facing you, wrap 3 turns of tape clockwise. Make sure the tape does not extend over the end of the horse barb, this will prevent blockage.
The stencil film is the secret behind making beautiful artwork. Simply copy the artwork from the internet, magazines, books onto the stencil film with any scanner/printer.
Stencil film has unique self adhesive film can be imaged on with a copier or printer. The image can then be cut out and applied to most surfaces by peeling off the backing. Use your Powercarver to trace the image resulting in a transfer of the image to your artwork.
Stencil film consists of a thin top film made from coated polyester film. The film is extremely tough considering its thinness. The top coating is specially formulated to allow toner and ink from your printer to adhere. You can also draw on the surface with pen or pencil.
Sheet size is 8 1/2 x 11 inches, only 1 mil thick, yet very tough. The film has a clear matte finish with a peel-off adhesive backing. Set your ink jet printer to "Draft", "Fast Print" or "Glossy Photo Paper". Sold in sheets of 5.
Minimum quantity for "Stencil and Transfer Film" is 5.
Vary the speed of your carver hands-free! This variable speed foot control pedal is a must have! It allows you to change the speed seamlessly with an easy to press foot pedal, leaving your hands free to hold the tool and your work simultaneously without interruptions from fumbling with hand controls. From off to full speed and everything in between, you'll be amazed how often you change your carving speed from moment to moment. With just a little change in foot pressure, you can change the speed to carve critically fine details or press down for fast carving. This foot pedal connects into your air hose to control the speed of your carver and comes with two brass hose barbs for easy hook-up. Just push your air hose onto the barbs and you have instant speed control. Your carving tool is off until you apply foot pressure to the pedal. The more you push the pedal, the faster your carver turns. The foot pedal uses an actual control valve connected to a long throw pedal to vary the air flow, unlike other foot pedals that pinch the air hose and can cause leaks and foot fatigue. Once you use a foot pedal like this, you'll wonder how you ever carved without it. This foot pedal is industrial grade and will last a lifetime.
Valveless fittings are completely interchangeable. Fitting halves seal with a twist; replaceable O-rings eliminate leaks. Use to disconnect tool from air supply. Fitting is 1/8" ID (fits our air hose). Rated to 100 psi.
2019 Unbridled, LLC. All rights reserved. All prices are in USD.