Clear air hose plastic tubing. Used to give you extra length between your carver and air compressor. Accepts 1/8 inch hose barbs.
Minimum quantity for "Air Hose Clear Tubing, only $0.95 per foot!" is 12.
This brass hose barb splicer allows you to connect two air hoses together by pushing the hose on to the barb. The splicer is designed for air hose with 1/8 inch inside diameter, like the hose that comes with most carvers and extra length of hose in this section. This splicer is all brass construction, will not rust or corrode. Precision machined to high quality standards.
The CAT-1610SPQ-DCO Quiet Air Compressor is designed to be one of the quietest air compressors in the industry having only 65 decibels of sound. Perfect for powering the Vortex F5 Ultra High Speed Precision Carver.
Female Brass Industrial Plug 1/4 NPT. Makes it easy to connect your air hose to your air compressor. If you have our air compressor with a quick release, get this matching part. It makes your air connections a snap!
Male Brass Hose Barb 1/4 NPT. Push on to 1/8 to 3/16 inch inside diameter hose. Threads are 1/4 NPT. Connect to your air compressor or filter and air hose.
Male Brass Hose Barb 1/8 NPT. Push on to 1/8 to 3/16 inch inside diameter hose. Threads are 1/8-27 NPT. These are used for the Speed Control Foot Pedal.
This combination air filter and water trap removes dirt & debris larger than 5 microns and helps catch condensed water. A must for improving the life of your turbine bearings. For best use, have at least 10 feet of hose between your air compress and this air filter/water trap. This will ensure the air has cooled and the water vapor has condensed where it can be collected by the water trap. Easy to connect. Your air compressor connects to the "IN" port and the Powercarver hose barb connect to the "OUT" port. When water collected is about 1/2 full in the clear bowl, open the release valve to drain the water. Remember to order 2 brass hose barbs to connect your air hose. The hose barbs are 1/4 NPT and push onto 1/8 inch inside diameter hose.
Valveless fittings are completely interchangeable. Fitting halves seal with a twist; replaceable O-rings eliminate leaks. Use to disconnect tool from air supply. Fitting is 1/8" ID (fits our air hose). Rated to 100 psi.
Vary the speed of your carver hands-free! This variable speed foot control pedal is a must have! It allows you to change the speed seamlessly with an easy to press foot pedal, leaving your hands free to hold the tool and your work simultaneously without interruptions from fumbling with hand controls. From off to full speed and everything in between, you'll be amazed how often you change your carving speed from moment to moment. With just a little change in foot pressure, you can change the speed to carve critically fine details or press down for fast carving. This foot pedal connects into your air hose to control the speed of your carver and comes with two brass hose barbs for easy hook-up. Just push your air hose onto the barbs and you have instant speed control. Your carving tool is off until you apply foot pressure to the pedal. The more you push the pedal, the faster your carver turns. The foot pedal uses an actual control valve connected to a long throw pedal to vary the air flow, unlike other foot pedals that pinch the air hose and can cause leaks and foot fatigue. Once you use a foot pedal like this, you'll wonder how you ever carved without it. This foot pedal is industrial grade and will last a lifetime.
Teflon® tape, also know as PTFE tape, is used to make a tight seal the threads for our brass hose barbs. With the threads facing you, wrap 3 turns of tape clockwise. Make sure the tape does not extend over the end of the horse barb, this will prevent blockage.
This valve controls the speed of your tool. Simply turn the knob to your desired speed from shut off to full speed and everything in between. Can be used with tank and tankless air compressors.
2019 Unbridled, LLC. All rights reserved. All prices are in USD.