F5 Turbine Bearing Service - Includes new sealed ceramic lube free bearings with your choice of Radial or Angular, wave/plate washers, o-rings - Both rear & front flanged bearings are sealed for dust & debris protection.
F5 Turbine Nosecone Assembly - Includes new spindle/collet, wave/plate Washers, 24 Vane Impeller, Ceramic Bearings - Both rear & front flanged (sealed for dust & debris protection, lube-free, radial or angular designed with o-rIngs), 7 jet port injector manifold, Fluted brass nosecone with 10 seated exhaust ports, New housing o-ring. Fully Assembled, just screw on to the Vortex F5 housing. Your choice of bearing and spindle type.
The Vortex Router Base (VRB) attachment is finally here! Specifically designed for the Vortex High Speed Carver, the VRB is precision milled from Aerospace aluminum in a user friendly ergonomic shape. The VRB will take your Vortex to the next level allowing you to precision carve the perfect uniform depth to inlay precious metals, stones, woods and/or epoxies like a pro! It also allows you to carve perfect depth lettering and borders as well. Its hourglass shape with a wide front viewing port makes it easy to see what you're doing and the chamfered face is milled to remove the sharp edge to provide a smooth router movement. The VRB gives you complete control over the depth at which you are engraving. Simply slide it onto the end of the Vortex carver and tighten the three set screws with the allen wrench provided and you're really to carve. The 3 Stainless Steel set screws have nylon points which provide extra gripping strength while at the same time will not scratch or mar the surface of your Vortex carver and will allow you to lock down the router at any desired depth. Get the Vortex Router Base attachment today and add an entire new dimension to your engraving! Just a reminder that we also sell spare set screws and allen wrenches in case you lose them as they are quite small. Ordering a spare set will keep you from having down time waiting for a separate order to be shipped to you in case you lose them.
Male Brass Hose Barb 1/8 NPT. Push on to 1/8 to 3/16 inch inside diameter hose. Threads are 1/8-27 NPT. These are used for the Speed Control Foot Pedal.
Teflon® tape, also know as PTFE tape, is used to make a tight seal the threads for our brass hose barbs. With the threads facing you, wrap 3 turns of tape clockwise. Make sure the tape does not extend over the end of the horse barb, this will prevent blockage.
Organize your burs with this 24 holes high quality plastic bur holder. Designed to hold standard FG type burs or any bur with a 1/16 inch (1.6mm) diameter shaft. Colors vary.
These 30 hole aluminum bur holders are designed to hold standard FG type burs or any bur with a 1/16 inch (1.6mm) diameter shaft. Anodized colors vary (gold shown in photo.)
Keeps diamond and stone cutters clean to maximize life. At normal hand piece cutting speed, cut into the cleaning stone for approximately two seconds. This removes debris from the diamond and stone burs and restores the cutting edges of diamond particles. For best results, moisten cleaning stone to clean more efficiently. The cleaning stone measures ¾"x¾"x3"
The stencil film is the secret behind making beautiful artwork. Simply copy the artwork from the internet, magazines, books onto the stencil film with any scanner/printer.
Stencil film has unique self adhesive film can be imaged on with a copier or printer. The image can then be cut out and applied to most surfaces by peeling off the backing. Use your Powercarver to trace the image resulting in a transfer of the image to your artwork.
Stencil film consists of a thin top film made from coated polyester film. The film is extremely tough considering its thinness. The top coating is specially formulated to allow toner and ink from your printer to adhere. You can also draw on the surface with pen or pencil.
Sheet size is 8 1/2 x 11 inches, only 1 mil thick, yet very tough. The film has a clear matte finish with a peel-off adhesive backing. Set your ink jet printer to "Draft", "Fast Print" or "Glossy Photo Paper". Sold in sheets of 5.
Minimum quantity for "Stencil and Transfer Film" is 5.
This combination air filter and water trap removes dirt & debris larger than 5 microns and helps catch condensed water. A must for improving the life of your turbine bearings. For best use, have at least 10 feet of hose between your air compress and this air filter/water trap. This will ensure the air has cooled and the water vapor has condensed where it can be collected by the water trap. Easy to connect. Your air compressor connects to the "IN" port and the Powercarver hose barb connect to the "OUT" port. When water collected is about 1/2 full in the clear bowl, open the release valve to drain the water. Remember to order 2 brass hose barbs to connect your air hose. The hose barbs are 1/4 NPT and push onto 1/8 inch inside diameter hose.
4" Magnetic Polished Stainless Steel Bur Tray. Stop losing burs! Put all your burs into the magnetic bur tray and pick and choose the ones you need for your project.
2020 Unbridled, LLC. All rights reserved. All prices are in USD.